Teste de Função ESP / ABS

f_galdino

Novato
Pessoal, bom dia!

Minha SPB esta com a luz ESP piscando, passei o vag (erro 01486) e pesquisei e vi que esta em modo de teste.

Fiz o procedimento de andar ate 20km virar o volante e tal mas continua.

Alguém sabe uma forma de resetar isso ? ou como fazer para apagar essa luz ?
 
Pessoal, bom dia!

Minha SPB esta com a luz ESP piscando, passei o vag (erro 01486) e pesquisei e vi que esta em modo de teste.

Fiz o procedimento de andar ate 20km virar o volante e tal mas continua.

Alguém sabe uma forma de resetar isso ? ou como fazer para apagar essa luz ?


@f_galdino

Tem um vídeo no YouTube (vou achar para você) que ensina a fazer o procedimento para apagar essa luz.

Vc precisa ir em um lugar fechado ou estacionamento de mercado e a 30km/H dirigir cerca de 200m fazer uma curva de 180º a esquerda, andar mais 200m e fazer outra curva a esquerda.

Se tudo estiver correto a luz some do painel.




Sent from my iPhone using Tapatalk - now Free
 
Amigo não sei.

Mais eu achei que fosse baboseira.

Mais um amigo teve esse problema fez isso e a luz do ABS sumiu.

Se a luz do controle de estabilidade continuar acesso é outra coisa.




Sent from my iPhone using Tapatalk - now Free
 

Ramacciotte

Novato
Alguém pode me ajudar, por favor ? Estava com problema para codificar a unidade do ABS após a troca. Com o vag consegui codificar apagando o aviso ( ! ) só que continuam a luz amarela do ESP e ABS.

No Vag apareceram os seguintes erros:

Address 03: ABS Brakes (-----) Labels: 1K0-907-379-60EC1F.clb
Part No SW: 1K0 907 379 AE HW: 1K0 907 379 AE
Component: ESP MK60EC1 H35 0106
Revision: 00H35001
Coding: 144260120A290001281306ED50190041B900
Shop #: WSC 04531 659 97518
VCID: 75EA56BEDC1620B6AC3
5 Faults Found
01486 - System Function Test Activated
000 - -
Freeze Frame:
Fault Status: 01100000
Fault Priority: 2
Fault Frequency: 1
Reset counter: 23
Mileage: 42641 km
Time Indication: 0
Date: 2013.10.27
Time: 12:14:16
Freeze Frame:
Count: 3
Count: 12
Count: 12800
Count: 320
Count: 49408
Count: 256
Count: 0
Count: 0
01279 - Longitudinal Acceleration Sensor (G251)
005 - No or Incorrect Basic Setting / Adaptation
Freeze Frame:
Fault Status: 01100101
Fault Priority: 2
Fault Frequency: 1
Reset counter: 23
Mileage: 42641 km
Time Indication: 0
Date: 2013.10.27
Time: 12:14:16
Freeze Frame:
Count: 3
Count: 12
Count: 12800
Count: 212
Count: 49408
Count: 256
Count: 0
Count: 0
01435 - Brake Pressure Sensor 1 (G201)
005 - No or Incorrect Basic Setting / Adaptation
Freeze Frame:
Fault Status: 01100101
Fault Priority: 2
Fault Frequency: 1
Reset counter: 23
Mileage: 42641 km
Time Indication: 0
Date: 2013.10.27
Time: 12:14:16
Freeze Frame:
Count: 3
Count: 12
Count: 12800
Count: 279
Count: 49408
Count: 256
Count: 0
Count: 0
00778 - Steering Angle Sensor (G85)
005 - No or Incorrect Basic Setting / Adaptation
Freeze Frame:
Fault Status: 01100101
Fault Priority: 2
Fault Frequency: 1
Reset counter: 23
Mileage: 42641 km
Time Indication: 0
Date: 2013.10.27
Time: 12:14:16
Freeze Frame:
Count: 3
Count: 12
Count: 12800
Count: 295
Count: 49408
Count: 256
Count: 0
Count: 0
01423 - Lateral Acceleration Sensor (G200)
005 - No or Incorrect Basic Setting / Adaptation
Freeze Frame:
Fault Status: 01100101
Fault Priority: 2
Fault Frequency: 1
Reset counter: 23
Mileage: 42641 km
Time Indication: 0
Date: 2013.10.27
Time: 12:14:16
Freeze Frame:
Count: 3
Count: 12
Count: 12800
Count: 270
Count: 49408
Count: 256
Count: 0
Count: 0
 
E só executar os 4 basics settings:

  • no site da ross tech tem o DIY segue abaixo:
Basic Setting

Sensor for Steering Angle (G85)
Prerequisites:
  • Start the vehicle.
  • Turn the steering wheel one turn to the right and one turn to the left.
  • Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
  • If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
  • Ensure that the steering wheel is not moved again.
  • Keep the engine running and do not switch off the ignition.
  • System voltage at least 12.0 V.
[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 °.
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
[Close Controller, Go Back - 06]
Note: After successful basic setting, the Steering Limit Stop needs to be adapted too.


Lateral Acceleration Sensor (G200)
Prerequisites:
  • System voltage at least 12.0 V.
[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 063
[Go!]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was successful, check the sensor again.
[Measuring Blocks - 08]
Group 004
[Go!]
Check field 2, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Close Controller, Go Back - 06]


Brake Pressure Sensor 1 (G201)
Prerequisites:
  • System voltage at least 12.0 V.
[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 005
[Go!]
Check field 1, the value has to be between -8.0 and +8.0 bar.
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 066
[Go!]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was successful, check the sensor again.
[Measuring Blocks - 08]
Group 005
[Go!]
Check field 1, the value has to be between -3.8 and +3.8 bar.
[Done, Go Back]
[Close Controller, Go Back - 06]


Longitudinal Acceleration Sensor (G251)
Prerequisites:
  • System voltage at least 12.0 V.
[Select]
[03 - Brake Electronics]
[Measuring Blocks - 08]
Group 006
[Go!]
Check field 4, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Security Access - 16]
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 069
[Go!]
After a successful basic setting, field 2 should say "OK".
[Done, Go Back]
To make sure the basic setting was successful, check the sensor again.
[Measuring Blocks - 08]
Group 006
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 m/s².
[Done, Go Back]
[Close Controller, Go Back - 06]
 

ALBERTOLIMA

Membro
Quem ainda estiver com o problema, é facil desativar essa porcaria de teste
Só entrar em ABS Brakes, BASIC SETTINGS, CANAL 103 , clicar em ON/OFF/NEXT

E pronto desativado.


Abraços
 
Topo